<300, 450, 600 CANS PER MINUTE

Depending on can size and product packed inside. To be confirmed each time.

Max. mechanical capacity of 250.000 cans/ shift.

GEAR DRIVEN LIFTERS

Allowing to seam thinner metal thickness at higher speeds.

Its excellent seaming quality is backed by the most renowned can makers.

MODULAR ASSEMBLY

Family of machines with 4, 6 or 8 seaming spindles.

One same mainframe with three different configurations depending on the requested capacity.

FOR ROUND CANS

For round cans with a max can diameter of 99 mm (401D).

Beverage aluminum cans 12 oz, 16 oz, picnic, buffet.

<300, 450, 600 CANS PER MINUTE

Depending on can size and product packed inside. To be confirmed each time.

Max. mechanical capacity of 250.000 cans/ shift.

GEAR DRIVEN LIFTERS

Allowing to seam thinner metal thickness at higher speeds.

Its excellent seaming quality is backed by the most renowned can makers.

MODULAR ASSEMBLY

Family of machines with 4, 6 or 8 seaming spindles.

One same mainframe with three different configurations depending on the requested capacity.

FOR ROUND CANS

For round cans with a max can diameter of 99 mm (401D).

Beverage aluminum cans 12 oz, 16 oz, picnic, buffet.

STAINLESS STEEL CANNING MACHINE

Fastest we ever produced

SAGA M series of canning machines consist of 3 models. Available with 4, 6 or 8 spindles, they cover productions from 50 to 600 cans/min and can be linked with all fillers available on the market.

Executions vary from atmospheric, steam vacuum, under cover gassing, liquid nitrogen dosing, clinching and can shop. JK SOMME offers a solution for all commonly produced round cans up to 99 mm diameter (401D) and heights up to 120 mm (250 mm under special order).

SAGA 4M

< 300 cans per minute
4 spindles

SAGA 6M

< 450 cans per minute
6 spindles

SAGA 8M

< 600 cans per minute
8 spindles

Stop overhauling your dinosaur era canning machine. Now you have an alternative

GEAR DRIVEN LIFTER PLATES & SEAMING CHUCKS

Over the years, in an effort to cut material costs, tin plate thickness has been gradually reduced. When using these new cans on some old canning machines, operators are forced to keep high lower chuck pressure and slow the machine down to avoid chuck slippage problems.

Gear driven lower lifters have the following advantages:

  • Increased capacity in cans/min.
  • Increased seam integrity.
  • Reduced slipping of covers on seaming chuck and increase in chuck working life.
  • Reduction in spring pressure, eliminating the problem of mushroom flanges.

Best solution for seaming thin wall cans

MODULAR ASSEMBLY CANNING MACHINE

Due to its clever engineering design and modular construction the 3 machines share almost 90% of parts enabling us to:

  • Reduce manufacturing costs.

  • Reduce delivery times. Ranging from 3-4 month depending on optionals.

  • Increase amount of available spare parts.​

Making stainless steel canning machines an option

FAST CAN HEIGHT REGULATION

Changing from one can height to another is always a main issue for a canning machine operator. With SAGA M changeovers are simple and extremely fast. The procces:

  1   Unscrew three main bolts (two in columns and one in main central shaft).

  2   With a special hand tool rotate a pinion located on the roof of the machine. Doing so the complete seaming turret as well as the lid feeder will move up/down till reaching the desired height.

  3   Tighten bolts again.

  4   YOU ARE DONE!

STANDARD FEATURES

  • Heavy duty construction.

  • 100% mechanical.

  • Stainless steel finish.

  • Family series with 90% parts commonality.​

  • CE compliance.​

  • Gear driven lifters.​

  • Easy-adjust chuck plate springs.​

  • Extended cover feed.​

  • No-Can-No-Cover.​​

  • Ultra fast can height adjustment.

  • Quick tooling changeover.

  • Mechanical filler drive with cardan shaft.

  • Stainless steel machine enclosure with built-in control cabinet.

  • Large service doors and wide access openings.​

  • Clean and sanitary design.​

  • Minimal effort required for maintenance.​​

  • Foam/chemical cleaning compatible.​​

  • Maximum safety for operator.​​

  • Easy operation.​​

  • Can counter.​​

  • CPM rate display.​​

  • Frequency drive.​​​

  • 230/380/400/460 VAC, 3 Phase, 50/60 Hz. W/ 24 VDC control voltage.​​

SAGA |4M |6M |8M 

Take advantage of this powerful canning machine and increase your capacity.

CANNING MACHINE SPECIFICATIONS

ACCEPTED CAN SIZES
  • Diameter range: 47 – 99 mm

  • Height Range: 30 – 120 mm (250 upon specific request)

KEY FEATURES
  • Rated speed – 4M: Up to 300 cans/minute

  • Rated speed – 6M: Up to 450 cans/minute

  • Rated speed – 8M: Up to 600 cans/minute

  • Seaming heads – 4M: Rotary carousel with 4 spindles

  • Seaming heads – 6M: Rotary carousel with 6 spindles

  • Seaming heads – 8M: Rotary carousel with 8 spindles

  • Can seaming op.: Rotary type

  • Second operation off-seam setting: Yes

  • Main drive gear box: Oil bath

  • Lubrication: Oil and Grease

  • Easy maintenance & greasing: Yes

  • Can infeed & outlet: Straight line

  • Can entrance to machine: By timing screw

  • Clincher: 6 stations rotary clincher with vertical motion

  • Cover separator: Single knife

  • Mechanical protection against overloads: Yes

  • No can/No cover feed: Yes

  • Parts made stainless to optimize hygienic design: 80%

  • Safety enclosure: Stainless steel with door interlocks following CE safety regulations

  • Internal lighting of the complete working area: By LED lights

  • Stainless steel spillage collecting tray covering machine frame: Yes

  • Quick cleaning & water drainage: Yes

  • Electronic variable speed motor drive: Yes

  • PLC: Yes

  • Kit of recommended spare parts: Yes

  • Tool kit and instruction manual: Yes

PRACTICAL FEATURES
  • Estimated tooling changeover:  3-4 hours

  • Can height changeover: 5 minutes

DIMENSIONS & CONSUMPTIONS
  • Overall dimensions (LxWxH): 2.637 x 1.530 x 1.891 mm

  • Can feeding conveyor height: 1000 mm

  • Net weight – 4M: 1700 Kg

  • Net weight – 6M: 1750 Kg

  • Net weight – 8M: 1800 Kg

  • Motor: 7.5 Hp

  • Compressed air: 40 L/H 6 Kg/cm3

OPTIONAL FEATURES
  • Can making version: Yes

  • Mechanical cover marker for a max of 2 rows x 7 marks: Yes

  • Filler connecting parts: Yes

  • Touch screen control panel: Yes

  • Extended lid chute with vibrator: Yes​

Do you want to talk to an expert?

Do you want to talk to an expert?

Menu